In flowerwood layering, the branches of the plant are buried in the soil, new roots are germinated using maternal nutrition, and the new plants are cut and cultivated. It is characterized by promoting rooting without losing the condition of the mother plant, high survival rate, and easy forming, but the operation is more annoying and the breeding capacity is small, which is suitable for family adoption.
1. Ordinary layering is suitable for clustered flowers and trees. Such as wax plum, spring, jasmine and so on. The method is: Select a 1-2 year-old branch near the ground on the base. Under the festival, use a knife to insult or peel the skin. Then, sew along the edge of the basin or in the rhizosphere, and bury the branches in the soil, with a depth of 10 to 12 cm. Use a wire nest to form a U-shape and hold the sticks down to prevent bouncing. Then cover the soil and expose the top tip to the ground. This method is mostly carried out in the early spring or late autumn. The spring bead is cut off in autumn and the autumn bead is cut off in spring.
2. The horizontal layering method is suitable for long branches or creeping flowers and trees. Such as rattan rose, ivy, Ling Xiao and so on. The branches and stems are bent on the soil surface or in the shallow ditch, and the soil is covered. After the roots are cut, they are cut off from the mother plant and planted separately. It is also possible to use a knife to inflict injuries at each section, and most of the young plants can be obtained at a time. The piled soil layer is suitable for multi-branch buds and branches that are not easy to bend. Such as the hydrangea, the June snow, the golden finches, and the paste of the sea bream. Before the lamination, the base skin is insulted and the soil is raised 20 to 30 centimeters upwards. The soil is often kept moist. After the roots have been planed, they are cut off from the mother plant and cultivated separately.
3. The high air pressure layer is suitable for the base not to have axillary buds, the branches are not easy to bend, and the cuttings are not easy to survive. Such as rose, sweet-scented osmanthus, Milan and so on. The high pressure is carried out in late spring and early summer. Generally, the two-year-old strong shoots are ring-skinned or scratched under the joints, reaching deep into the cortex with a width of 1.5 to 2 times the diameter of the branches. After being treated with rooting hormones, about 5 cm at the lower end of the incision, the plastic film is tied, and then rolled up, filled with moss or mud, and put on the mouth to leave a gap to facilitate watering and rainwater. Afterwards, the substrate is often kept wet until the roots are cut off in the fall to plant or potted plants. After another 1 to 2 years, it can bloom and be used for viewing.
1. Ordinary layering is suitable for clustered flowers and trees. Such as wax plum, spring, jasmine and so on. The method is: Select a 1-2 year-old branch near the ground on the base. Under the festival, use a knife to insult or peel the skin. Then, sew along the edge of the basin or in the rhizosphere, and bury the branches in the soil, with a depth of 10 to 12 cm. Use a wire nest to form a U-shape and hold the sticks down to prevent bouncing. Then cover the soil and expose the top tip to the ground. This method is mostly carried out in the early spring or late autumn. The spring bead is cut off in autumn and the autumn bead is cut off in spring.
2. The horizontal layering method is suitable for long branches or creeping flowers and trees. Such as rattan rose, ivy, Ling Xiao and so on. The branches and stems are bent on the soil surface or in the shallow ditch, and the soil is covered. After the roots are cut, they are cut off from the mother plant and planted separately. It is also possible to use a knife to inflict injuries at each section, and most of the young plants can be obtained at a time. The piled soil layer is suitable for multi-branch buds and branches that are not easy to bend. Such as the hydrangea, the June snow, the golden finches, and the paste of the sea bream. Before the lamination, the base skin is insulted and the soil is raised 20 to 30 centimeters upwards. The soil is often kept moist. After the roots have been planed, they are cut off from the mother plant and cultivated separately.
3. The high air pressure layer is suitable for the base not to have axillary buds, the branches are not easy to bend, and the cuttings are not easy to survive. Such as rose, sweet-scented osmanthus, Milan and so on. The high pressure is carried out in late spring and early summer. Generally, the two-year-old strong shoots are ring-skinned or scratched under the joints, reaching deep into the cortex with a width of 1.5 to 2 times the diameter of the branches. After being treated with rooting hormones, about 5 cm at the lower end of the incision, the plastic film is tied, and then rolled up, filled with moss or mud, and put on the mouth to leave a gap to facilitate watering and rainwater. Afterwards, the substrate is often kept wet until the roots are cut off in the fall to plant or potted plants. After another 1 to 2 years, it can bloom and be used for viewing.
Dingmin Pharmaceutical supply Alogliptin API and Alogliptin Intermediates with high purity and best price. The main products CAS No are as follows: 850649-62-6, 4318-56-3, 865758-96-9. Sample can be sent if you request.
Welcome to do business with us. Please email to us directly.
Alogliptin Benzoate,Alogliptin Intermediates,Cas 865758-96-9
Shijiazhuang Dingmin pharmaceutical Sciences Co.,Ltd , https://www.dingminpharma.com