Operating procedures and daily maintenance:
1. This machine uses 220V single-phase three-wire power supply, the grounding must be reliable, otherwise it will affect personal safety.
2. The metal parts cannot be close to the sensor head.
3. Check the cooling water level frequently. When it is used frequently, check it once a week and replenish the cooling water. Zui is good to use non-conductive cooling water.
4, often check the pipeline, the joints can not have water leakage, water seepage. In order to prevent the pipe from freezing due to low temperature, antifreeze should be injected into the water tank.
5, maintenance should follow the order of operation.
6, maintenance should be fixed professionals.
7. Do not open the chassis after booting. The total power must be cut off when checking maintenance.
8. The machine is designed with overload and overheat protection system. When the temperature of the heat sink exceeds 70 degrees, the high voltage will be cut off, and the warning light will flash: when the load is too large (that is, the heated cap is too large or closely arranged or too close to the induction head), the high voltage current of the machine is instantaneously overloaded (digital display) It can also be protected by instantaneously exceeding "100"). This is normal and can be initiated by pressing the "START" button again.
Cleaning and maintenance Regularly clean the surface of the machine, the bottom plate and the lower mold slide, the groove, the upper mold inner pressure plate and the positioning rod (Note: the power must be turned off and the normal temperature is restored). The lower die slide, the pressure bar bearing, the eccentric wheel and the guide post, the guide rail and other transmission parts are regularly added with butter to ensure the performance of the machine. To clean the cutter: first use the cotton ball to plug the two drain holes of the lower mold, pour the boiling water into the groove of the lower mold, fill it up, then push the lower mold slide into place, press the upper mold down, press To the low point of zui, let the tooth knife soak for a few minutes until it is clean, and repeat it several times.
1. This machine uses 220V single-phase three-wire power supply, the grounding must be reliable, otherwise it will affect personal safety.
2. The metal parts cannot be close to the sensor head.
3. Check the cooling water level frequently. When it is used frequently, check it once a week and replenish the cooling water. Zui is good to use non-conductive cooling water.
4, often check the pipeline, the joints can not have water leakage, water seepage. In order to prevent the pipe from freezing due to low temperature, antifreeze should be injected into the water tank.
5, maintenance should follow the order of operation.
6, maintenance should be fixed professionals.
7. Do not open the chassis after booting. The total power must be cut off when checking maintenance.
8. The machine is designed with overload and overheat protection system. When the temperature of the heat sink exceeds 70 degrees, the high voltage will be cut off, and the warning light will flash: when the load is too large (that is, the heated cap is too large or closely arranged or too close to the induction head), the high voltage current of the machine is instantaneously overloaded (digital display) It can also be protected by instantaneously exceeding "100"). This is normal and can be initiated by pressing the "START" button again.
Cleaning and maintenance Regularly clean the surface of the machine, the bottom plate and the lower mold slide, the groove, the upper mold inner pressure plate and the positioning rod (Note: the power must be turned off and the normal temperature is restored). The lower die slide, the pressure bar bearing, the eccentric wheel and the guide post, the guide rail and other transmission parts are regularly added with butter to ensure the performance of the machine. To clean the cutter: first use the cotton ball to plug the two drain holes of the lower mold, pour the boiling water into the groove of the lower mold, fill it up, then push the lower mold slide into place, press the upper mold down, press To the low point of zui, let the tooth knife soak for a few minutes until it is clean, and repeat it several times.
We provide double pp ports of various specifications for infusion soft bags, and we adopt advanced equipment and mould to ensure the quality of the products. Our ports have technical patent and low welding temperature.This lead to a higher product yield and lower bag leakage rate.Our products have good compatibility with drugs.The first-class workshop environment ensures the cleanliness of the product.
Double Port,Dual Port,Double Usb Port,Double Input Port
SUZHOU CRH PHARMACEUTICAL TECHNOLOGY CO.,LTD , https://www.crh-health.com